Estimating and Design Services in Illinois
Illinois moved to the 2024 Illinois Energy Conservation Code on November 30, 2025, so anything older than that is out of date. Chicago then layers its own building, electrical and plumbing requirements on top, including conduit-only wiring and a sprinkler threshold that catches most new residential work. Outside the city, each suburb runs its own permit desk, and the collar counties are not interchangeable. Typical fee is $300 to $2,500 depending on trade count and project size. Estimates are billed at $30-$45 per hour.
Illinois moved to a 2024 IECC-based energy code on November 30, 2025, and Chicago adds its own provisions plus a district energy network that replaces the mechanical plant entirely.

Estimating and Design Around Illinois's Codes and Climate
Illinois changed its statewide energy code twice in two years. The 2021 IECC took effect on January 1, 2024, and the 2024 IECC replaced it on November 30, 2025, which means a drawing set prepared a year ago may already be out of step with the edition governing the permit. Chicago then layers its own building and energy provisions on top of the state code, and downtown Chicago has an extensive district heating and cooling network where the mechanical room is largely an interface rather than a plant. Add Climate Zone 5 design conditions, one of the largest data center construction markets in the country, and a prevailing wage law with county-by-county rates, and Illinois becomes a state where the jurisdiction and the energy source decide more of the cost than the building type does.
What Makes Illinois Different
Energy Code
The 2024 Illinois Energy Conservation Code, based on the 2024 IECC, has been effective since November 30, 2025, replacing the 2021-based edition that applied from January 1, 2024. The City of Chicago maintains its own provisions on top of it.
Climate & Load Profile
IECC Climate Zone 5A across the state. Cold winters and warm humid summers, so both heating plant capacity and cooling with dehumidification are real scope drivers.
Prevailing Wage
Required on public works under the Illinois Prevailing Wage Act, 820 ILCS 130, with rates published by county and trade and certified payroll required. Private work is not covered; federal projects follow Davis-Bacon.
Common Project Types
Data centers, commercial office and tenant fit-out, healthcare, higher education, industrial and manufacturing, distribution, and multifamily.
Cities We Serve in Illinois
Illinois Codes We Estimate Against
Illinois updated its statewide energy code on November 30, 2025. A takeoff built on the 2021-based edition is now out of date, and Chicago adds its own layer on top.
| Code / Standard | Governing edition in Illinois | Where it hits the estimate |
|---|---|---|
| Illinois Energy Conservation Code | 2024 IECC-based edition effective November 30, 2025, replacing the 2021-based edition that applied from January 1, 2024 | Envelope values, fenestration, HVAC efficiency, economizers, duct insulation, lighting power density, controls |
| Capital Development Board adoption | CDB adopts and publishes the Illinois Energy Conservation Code with an effective date | Which edition governs the permit, and whether an existing set must be updated before bidding |
| City of Chicago building and energy provisions | Chicago maintains its own code requirements on top of the state edition | Additional review scope, metering, and energy provisions inside city limits |
| Illinois Mechanical and Plumbing Codes | State-adopted I-code editions with Illinois amendments | Ventilation rates, commercial kitchen exhaust, refrigerant piping, fixture units, gas piping |
| NFPA 70 (NEC) | Adopted through the state code with Illinois amendments | Service and feeder sizing, surge protection, emergency circuits, EV readiness |
| 820 ILCS 130 Prevailing Wage Act | Applies to public works construction | Labor rates by county and trade, certified payroll, and subcontractor compliance |
Illinois has changed its energy code twice since 2024. Confirm the edition in force at permit application before pricing a bid.
Regional Markets We Estimate Across Illinois
Chicago is effectively its own market with its own code, energy network, and labor agreements. Downstate runs on different economics entirely.
| Market | What drives construction | Dominant MEP scope | Estimating nuance |
|---|---|---|---|
| Downtown Chicago and the central area | Office repositioning, hospitality, institutional, high-rise residential | District heating and cooling interfaces, heat exchangers, condensate handling, metering, high-rise plumbing | The district energy interface replaces the plant and must be priced as its own system |
| Suburban Chicago and the collar counties | Data centers, distribution, corporate office, healthcare, laboratory | Medium-voltage distribution, UPS and generation, process cooling, lab exhaust, fire protection | Data center work is priced by capacity and redundancy tier, not by square footage |
| Rockford and Northern Illinois | Advanced manufacturing, aerospace, logistics, healthcare | Industrial ventilation, high-bay HVAC, process cooling, compressed air | Colder design conditions than Chicago increase heating plant size and freeze protection scope |
| Springfield and Central Illinois | State government, healthcare, higher education, agriculture | Central plants, medical gas, precision environment HVAC, backup power | Public and institutional work commonly carries prevailing wage and certified payroll requirements |
| Peoria and the Illinois River corridor | Heavy manufacturing, agriculture and processing, logistics | Process cooling, industrial ventilation, heavy power distribution, water treatment support | Industrial labor basis with outage windows and tie-in sequencing priced as scope |
Code jurisdiction, energy source, and labor agreements vary widely within Illinois. These are the five markets where most of our Illinois volume sits.
What Changes Between Illinois Markets
Illinois has one energy code and a lot of local authority. Chicago is effectively its own jurisdiction, and the suburbs around it are not consistent with each other.
| Market | What the jurisdiction adds | Where it shows up in the price |
|---|---|---|
| Chicago | Chicago Building Code, Chicago Electrical Code and Chicago Plumbing Code, all with local amendments on top of the state | Conduit-only wiring, stricter plumbing materials and a sprinkler threshold that puts fire protection into projects that would not need it in Naperville |
| Cook and the collar counties | Each suburb runs its own permit office, its own amendments and its own inspection schedule | A project spanning three suburbs can need three submittals. We price one estimate and flag where the scope diverges |
| Naperville, Schaumburg, Oak Brook | State energy code with local amendments, plus a commercial market that expects current-generation equipment | Higher efficiency baselines and more controls scope than a downstate project of the same size |
| Rockford and northern Illinois | State code, colder design conditions, heavy industrial base | Heating plant capacity, freeze protection and process utilities. Older buildings mean existing systems get surveyed before pricing |
| Peoria and central Illinois | State code, manufacturing and agriculture, river flood exposure in places | Industrial ventilation and process cooling, plus flood elevation where the site is near the river |
| Champaign and Metro East | State code, university and research work in Champaign, data center clusters near Edwardsville | Lab exhaust and make-up air in Champaign. Metro East projects sit in the St. Louis labor market, not the Chicago one |
Chicago's electrical and plumbing requirements are more restrictive than the state's. A set of drawings that is fine in Springfield may need a full redesign in the city.
What an Illinois MEP Estimate Costs
The fee is set by construction value and trade count. Chicago work costs more to build, but the estimating fee does not change because of the zip code.
| Project construction value | Our estimating fee | What pushes it toward the top of the range |
|---|---|---|
| Under $500K | $300 to $1,200 | A Chicago fit-out where the conduit, sprinkler and plumbing requirements add scope a suburban job of the same size does not carry |
| $500K to $2M | $1,000 to $2,500 | Four trades, a real spec book, and either a district energy interface or a full sprinkler design |
| $2M to $10M | $2,000 to $5,000 | Public work under the Illinois Prevailing Wage Act, healthcare or lab systems, or a data hall electrical package |
| $10M and up | $4,000 to $12,000+ | Multi-building campus work, phased occupancy, central plants and long-lead switchgear |
Fee ranges, not construction cost. Chicago union labor and suburban open-shop labor produce very different construction numbers from identical drawings.
24-48 Hour Turnaround on standard Illinois estimate requests.
Estimating Services by Trade
Illinois trade estimates price the 2024 Illinois Energy Conservation Code scope, whether that is a Chicago district energy interface, a Chicagoland data hall, or a downstate healthcare plant.
Illinois Estimating and Design Questions
Which Illinois energy code applies in 2026?
Illinois adopted the 2024 IECC through the Capital Development Board with an effective date of November 30, 2025, replacing the 2021 edition that had applied since January 1, 2024. Projects applying for a permit on or after November 30, 2025 must comply with the 2024-based code. The City of Chicago maintains its own provisions on top of it.
How is district heating priced in Chicago estimates?
Downtown Chicago has an extensive district heating and cooling network, so instead of boilers and chillers you price heat exchangers, steam or hot-water converters, condensate handling, pressure reducing stations, metering, and the interface with building distribution. We price the district energy interface separately so it can be compared against an on-site plant.
How do you estimate data center MEP in Illinois?
Chicagoland is one of the largest data center construction markets in the country. Those projects are priced by capacity and redundancy tier: medium-voltage switchgear and substations, UPS modules and batteries, standby generation with paralleling gear, cooling plant, pre-action suppression, and aisle containment. A Tier III and a Tier I design of the same square footage differ by multiples in MEP cost.
Does Illinois prevailing wage apply to my project?
Illinois has a prevailing wage law under the Prevailing Wage Act, 820 ILCS 130, applying to public works construction. Rates are published by the Illinois Department of Labor by county and trade, and certified payroll is required. Privately funded work is not covered, and federally funded projects follow Davis-Bacon.
What do you need to deliver an Illinois estimate in 24-48 hours?
Full drawings (A, S, MEP), the spec book, and the address. The address decides three things here: whether Chicago amendments apply, whether district energy is available at the site, and which labor market sets the rates. Deliverable is marked-up drawings, PDF, and Excel quantities by division.
Illinois MEP Estimating Guides
Get Your Illinois Estimate
Submit your plans and receive a detailed, line-item estimate, with most standard requests in 24-48 hours, confirmed with your quote.