Estimating and Design Services in California
California is the one state where the energy code is the price. Title 24 Part 6 sets the envelope, lighting and mechanical efficiency floor, and the 2025 edition applies to permit applications from January 1, 2026. Add the climate zone, which is assigned by street address, and seismic restraint, which is a counted quantity here rather than a note, and a California estimate stops looking like a national one. Typical fee is $300 to $2,500 by trade count and project size. Estimates are billed at $30-$45 per hour.
California estimates run on the 2025 Title 24 Part 6 standards from January 1, 2026, with compliance assigned by climate zone and seismic restraint counted as a real quantity in every trade.

Estimating and Design Around California's Codes and Climate
California is the only state where the energy code routinely changes the equipment schedule rather than just the envelope. The 2025 Title 24 Part 6 standards took effect on January 1, 2026, and they expand heat pump requirements, battery storage provisions, and indoor air quality measures on top of the 2022 edition. Compliance is demonstrated through software modeling on either a performance or prescriptive path, which means the code edition decides which systems are even allowed before cost enters the conversation. Layered on top are 16 climate zones, a seismic design category that varies by site, and a public works prevailing wage regime that requires DIR registration. We assign the zone, the seismic category, and the labor basis by project address, then price the compliance path the design team actually intends to use.
What Makes California Different
Energy Code
The 2025 Building Energy Efficiency Standards (Title 24 Part 6) apply to permit applications submitted on or after January 1, 2026, replacing the 2022 edition. CalGreen (Title 24 Part 11) applies alongside it.
Climate & Load Profile
16 distinct climate zones statewide, from coastal fog belts with minimal cooling to inland zones with high cooling loads. The zone is assigned by project address, not by metro area.
Prevailing Wage
Required on public works, with contractors and subcontractors registered with the Department of Industrial Relations and certified payroll reporting. Private commercial work is generally exempt; federal work follows Davis-Bacon.
Common Project Types
Technology and office, life sciences and laboratory, healthcare, higher education, multifamily, data centers, and industrial and logistics.
Cities We Serve in California
California Codes We Estimate Against
Title 24 is not a single document, and the energy provisions are only one part of what governs an MEP design. Each part has to be confirmed against the project's compliance path.
| Code / Standard | Governing edition in California | Where it hits the estimate |
|---|---|---|
| Title 24 Part 6, Energy Code | 2025 Building Energy Efficiency Standards, effective January 1, 2026, replacing the 2022 edition | Envelope, fenestration, HVAC efficiency, heat pump requirements, lighting power density, controls, battery storage readiness |
| Title 24 Part 11, CalGreen | 2025 edition, applying alongside the energy code | Construction waste, indoor air quality measures, water efficiency fixtures, EV and bicycle infrastructure |
| Title 24 Part 4, Residential | 2025 edition for residential occupancies | Multifamily mechanical ventilation, water heating, envelope, and duct requirements |
| California Building Code, ASCE 7 Chapter 13 | Nonstructural seismic provisions adopted through the CBC | Sway bracing on ducts, seismic restraints on pipe and equipment, flexible couplings, anchorage calculations |
| NFPA 70 (NEC) | Adopted through the California Electrical Code with state amendments | Service and feeder sizing, surge protection, PV interconnection, EV charging infrastructure |
| Labor Code public works and DIR registration | Prevailing wage and registration requirements on public works | Labor rates, certified payroll, and subcontractor eligibility on publicly funded work |
Code editions and local amendments change. Confirm the edition in force at permit application, and the compliance path, before pricing a bid.
Regional Markets We Estimate Across California
Climate zone, seismic category, and labor basis all change by region. Each estimate is assigned to the correct basis, never a statewide average.
| Market | What drives construction | Dominant MEP scope | Estimating nuance |
|---|---|---|---|
| Los Angeles / Los Angeles County | Office and entertainment, healthcare, multifamily, transit-oriented development | Chilled water and VRF, high-rise plumbing, seismic restraint, fire alarm networks | Title 24 heat pump provisions and seismic bracing both add measurable scope over a code-minimum baseline |
| San Francisco Bay Area | Technology campuses, life sciences, high-rise office and residential | Heat pump plants, lab exhaust, cleanroom support, tenant sub-metering | Highest labor rates in the state, and lab exhaust drives mechanical cost far above office benchmarks |
| San Diego | Defense and life sciences, hospitality, biotech manufacturing, multifamily | Precision environment HVAC, process cooling, backup power, corrosion-resistant equipment | Coastal climate reduces cooling load but defense work can carry Davis-Bacon wage determinations |
| Sacramento and the Central Valley | State government, agriculture and food processing, distribution, healthcare | High-volume DX cooling, process refrigeration, warehouse MEP shells | Inland zones carry much higher cooling design loads than coastal zones in the same code cycle |
| Inland Empire and Central Coast | Logistics and warehousing, data centers, manufacturing, coastal hospitality | High-bay ventilation, process cooling, medium-voltage distribution, fire protection | Data center capacity work is priced by redundancy tier; logistics shells stay on a lighter labor basis |
Climate zones, seismic categories, and labor rates vary widely within California. These are the five markets where most of our California volume sits.
What Changes Between California Markets
Title 24 is statewide, but the climate zone, the local reach code and the review authority are not. The zone is set by the project address, and two buildings twenty miles apart can carry different envelope and mechanical requirements.
| Market | What the jurisdiction adds | Where it shows up in the price |
|---|---|---|
| Los Angeles | LADBS review, climate zones 6 through 9 depending on the address, plus local green building and seismic provisions | Cooling loads swing widely inside the county. A coastal address and a San Fernando Valley address get different equipment selections from the same drawings |
| San Francisco | SFDBI review, climate zone 3, and a local reach code that goes beyond Title 24 in places | Mild climate, so heating is small and there is often no cooling at all. The money sits in ventilation, seismic bracing and the review cycle |
| San Diego | Climate zone 7, coastal salt exposure, and city review with a separate fire plan check | Corrosion allowances on rooftop equipment and a fire review that runs on its own timeline |
| San Jose and the South Bay | Climate zone 4, with several cities in the county running their own reach codes | A project touching three cities can face three different reach code packages. We price to the strictest one the permit will actually see |
| Sacramento | Climate zone 12, state-level review for state-owned buildings, and hot inland summers | Real cooling loads and real heating loads in the same building. Both plants are sized, neither is a throwaway |
| Fresno and the Central Valley | Climate zone 13, the hottest inland conditions in the state, and heavy agricultural and food processing work | Cooling and refrigeration dominate. Process loads and ambient design temperatures push equipment selection well past a standard office package |
Hospitals fall under HCAI review and public schools under DSA. Both add plan check cycles and structural interaction that a private commercial project never sees.
What a California MEP Estimate Costs
The fee is set by construction value and trade count. California does not get a surcharge, but public work does bring prevailing wage and certified payroll into the labor basis.
| Project construction value | Our estimating fee | What pushes it toward the top of the range |
|---|---|---|
| Under $500K | $300 to $1,200 | Title 24 compliance documentation on a small tenant improvement, where the paperwork is a bigger share of the job than the pipe |
| $500K to $2M | $1,000 to $2,500 | Seismic restraint counted as a quantity in every trade, plus a reach code that exceeds the state baseline |
| $2M to $10M | $2,000 to $5,000 | Prevailing wage on public work, HCAI or DSA review, and lab or healthcare systems that need equipment quoted |
| $10M and up | $4,000 to $12,000+ | Multiple buildings, phased occupancy, central plants, and long-lead switchgear where lead time drives the schedule more than price |
Fee ranges, not construction cost. California construction pricing varies more by labor market than by code, and the Bay Area is not the Central Valley.
24-48 Hour Turnaround on standard California estimate requests.
Estimating Services by Trade
California trade estimates price the 2025 Title 24 scope, whether that is an LA high-rise, a Bay Area lab, or a San Diego healthcare project.
California Estimating and Design Questions
Which California energy code applies to projects permitted in 2026?
The 2025 Building Energy Efficiency Standards, Title 24 Part 6, apply to permit applications submitted on or after January 1, 2026, replacing the 2022 edition. They expand heat pump requirements, battery storage provisions, and indoor air quality measures. Because compliance is demonstrated through modeling, the code edition changes the equipment selections, not just envelope values.
How do California climate zones affect a mechanical estimate?
California defines 16 climate zones, and the zone drives envelope requirements, heating and cooling design conditions, and whether a heat pump or gas-hydronic solution is cost-effective. Coastal zones with mild summers behave nothing like inland zones with high cooling loads, so we assign the zone by project address rather than by metro area.
How much does seismic restraint add to California MEP scope?
It varies by site and system and should never be a blanket percentage. Nonstructural components fall under ASCE 7 Chapter 13 as adopted through the California Building Code, which means sway bracing on ducts, seismic restraints on piping and equipment, flexible couplings, threaded-rod stiffeners, and anchorage calculations. We count bracing by run length and restraint type.
Does prevailing wage apply to California projects?
Yes, on public works. California requires contractors and subcontractors on public works to be registered with the Department of Industrial Relations and to pay prevailing wages with certified payroll reporting. Private commercial work is generally not covered, and federally funded projects follow Davis-Bacon.
What do you need to deliver a California estimate in 24-48 hours?
Architectural, structural and MEP sheets, the spec book, and the address. The address is the one that matters: it fixes the climate zone, the seismic design category, and any local amendments sitting on top of Title 24. You get marked-up drawings back, plus a PDF summary and an Excel quantity sheet broken out by CSI division.
California MEP Estimating Guides
Get Your California Estimate
Submit your plans and receive a detailed, line-item estimate, with most standard requests in 24-48 hours, confirmed with your quote.