Part of MEP Design & Drafting ServicesDesign & Drafting

Revit MEP Modeling Services

Revit MEP modeling produces mechanical, electrical, and plumbing models at LOD 300, 350, or 400, built for design teams and contractors following a BIM execution plan. Turnaround depends on model complexity and level of detail. We confirm the exact timeline with your quote. Estimates are billed at $30-$45 per hour.

Mechanical, electrical, and plumbing Revit models at LOD 300, 350, or 400, built to your project's BIM execution plan.

A Revit MEP model is only as useful as the level of development it's built to, and building to the wrong LOD for the project phase is a common source of wasted modeling effort. LOD 300 models show mechanical, electrical, and plumbing systems sized and positioned accurately enough for design coordination, equipment is placed, ductwork and piping are routed, but connection detail between systems is still approximate. LOD 350 adds the interface and connection detail between trades and systems that formal clash detection actually requires, hanger types, support locations, and the physical interfaces where one trade's work meets another's. LOD 400 goes further still, modeling fabrication-level detail, exact routing, specific hanger and support placement, and connection methods, suitable for output that drives fabrication directly rather than just informing it.

We build every model against the project's BIM execution plan rather than our own internal modeling standard, since a model that doesn't follow the BEP's naming conventions, model organization, and file-sharing protocol creates friction for every other discipline trying to federate their model with ours. That means confirming LOD requirements by project phase (a BEP often specifies LOD 300 for design development and LOD 350 or 400 for construction documents), model element naming and parameter standards, and the coordinate system and shared file location the whole design team is using before we start modeling, not after.

Many projects don't start with a native Revit model at all, design intent exists as 2D CAD drawings, and we convert that 2D information into a coordinated 3D Revit MEP model built to the LOD the project needs. This happens most often on renovation and tenant improvement projects where the base building was never modeled in Revit, or on new construction where the design team worked in 2D through early phases and needs a 3D model for construction-phase coordination. Either way, the output is a model ready to federate with architectural and structural models for clash detection, not just a standalone MEP model sitting in isolation.

Every Deliverable, Itemized

  • Mechanical, electrical, and plumbing Revit models at LOD 300, 350, or 400
  • Model construction following the project's BIM execution plan (BEP)
  • 2D-to-3D conversion for projects without an existing native Revit model
  • Equipment, ductwork, piping, and conduit modeled to the specified LOD
  • Model organization and parameter standards aligned with your BEP
  • Federation-ready models for coordination with architectural and structural models

Is This Service Right for You?

  • Design-build teams that need a coordinated 3D MEP model for construction phase
  • General contractors federating trade models for clash detection and coordination
  • Owners or design teams converting 2D legacy drawings into a usable BIM asset
  • Mechanical, electrical, or plumbing subcontractors needing a model for fabrication output

Turnaround Depends on Scope, confirmed with your quote.

Common Questions

What's the difference between LOD 300, 350, and 400 for MEP models?

LOD 300 models show systems sized and located accurately enough for design coordination. LOD 350 adds connection and interface detail between systems and trades, needed for clash detection. LOD 400 adds fabrication-level detail, exact routing, hangers, and supports, suitable for direct-to-fabrication output.

Do you build models to our project's BIM execution plan?

Yes. We follow the project's BIM execution plan (BEP) for naming conventions, model organization, LOD requirements by phase, and file-sharing protocol, rather than building a model in our own standard and asking the rest of the team to adapt to it.

Can you model from 2D drawings if a Revit model doesn't already exist?

Yes. We regularly build Revit MEP models from 2D CAD drawing sets when no native Revit model exists, converting duct, pipe, and electrical layouts into a coordinated 3D model suitable for clash detection and construction documentation.

Ready to Get Started?

Submit your drawings or BEP requirements for a Revit MEP modeling quote.