Retail & Restaurant

Retail & Restaurant MEP Estimating

Retail and restaurant MEP estimating covers hood exhaust, makeup air, and grease interceptors for tenants and contractors working on fast-turnaround buildouts. Most estimates are delivered in 24-48 hours, with pricing typically $300-$2,000 depending on buildout scope. Estimates are billed at $30-$45 per hour.

Hood exhaust, makeup air, grease interceptors, and tenant improvement scope, priced for fast-moving buildout schedules.

Restaurant kitchen MEP scope carries more interdependent systems per square foot than almost any other tenant improvement, and getting one piece wrong usually breaks another. Hood exhaust is sized against the specific cooking equipment under each hood, not a flat CFM-per-linear-foot rule, since a hood over a charbroiler and fryer line needs meaningfully more exhaust capacity than one over a line of ovens and steamers. Makeup air has to be sized and priced as its own system rather than assumed to come from the building's general HVAC, because an undersized makeup air system depressurizes the kitchen and causes the hood to pull improperly, drawing conditioned air from the dining room or, worse, pulling combustion gases back into occupied space, regardless of how correctly the exhaust fan itself was sized.

Grease interceptors and the waste piping serving them are a frequent point of plan review rejection when undersized, so we size interceptors against the kitchen's fixture count and flow rate per the local plumbing code's specific requirements, not a generic restaurant-size estimate. Domestic water and gas piping for kitchen equipment, ranges, fryers, steamers, dish machines, is taken off against the actual equipment schedule and connection requirements rather than assumed from a typical kitchen layout, since equipment packages vary enormously between a quick-service concept and a full-service kitchen with a show kitchen or exhibition cooking line. Retail spaces without a commercial kitchen carry a different but equally real MEP profile: HVAC sized for high occupant turnover and display lighting loads, and electrical scope driven by point-of-sale systems, security, and merchandising lighting rather than cooking equipment.

Tenant improvement scope in both retail and restaurant work has to be separated cleanly from landlord-provided base building infrastructure, since lease agreements typically define exactly where landlord responsibility ends and tenant improvement begins, at the point of connection for electrical service, HVAC tap-in, or sanitary stub-out, for example. We flag that separation explicitly in the takeoff so your bid reflects only the scope you're actually responsible for pricing. Because retail and restaurant buildouts commonly run on compressed landlord delivery schedules where delay means losing a negotiated rent-free buildout period, we treat fast turnaround on this project type as a priority, not just a stated policy.

What Makes This Industry Unique

  • Hood exhaust and makeup air are interdependent systems that must be sized together
  • Grease interceptor sizing is a frequent plan review rejection point when undersized
  • Kitchen equipment schedules drive gas and water piping far more than typical building use
  • Base building vs. tenant improvement scope split is defined by the lease, not guesswork
  • Compressed landlord delivery schedules make turnaround speed a real cost factor

Key MEP Systems for This Building Type

  • Kitchen hood exhaust sized to cooking equipment load
  • Makeup air systems sized to replace exhausted kitchen air
  • Grease interceptors and kitchen waste piping sized to code
  • Gas and domestic water piping sized to the kitchen equipment schedule
  • Retail HVAC and electrical sized for occupant turnover and merchandising loads

24-48 Hour Turnaround on standard requests.

Common Questions

Do you estimate kitchen hood exhaust and makeup air separately?

Yes. Hood exhaust CFM is sized against the specific cooking equipment under each hood, and makeup air is sized and priced as its own system to replace the exhausted air, since an undersized makeup air system will depressurize the kitchen and cause the hood to pull improperly regardless of exhaust fan capacity.

Are grease interceptors included in a restaurant plumbing estimate?

Yes. Grease interceptors are sized based on the kitchen's fixture count and flow rate per local code requirements, and we price them along with the associated waste piping as a distinct line item, since interceptor sizing is a common point of plan review rejection when undersized.

How fast can you turn around a retail tenant improvement estimate?

Standard turnaround is 24-48 hours. Retail and restaurant tenant improvement projects typically run on compressed landlord delivery schedules, and we prioritize fast turnaround on this project type specifically because delay here often means losing negotiated rent-free buildout periods.

Ready to Get Started?

Submit your retail or restaurant buildout drawings for a fast, detailed MEP estimate.